BIER Ping and Trace
draft-ietf-bier-ping-08
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Active".
|
|
|---|---|---|---|
| Authors | Nagendra Kumar Nainar , Carlos Pignataro , Nobo Akiya , Lianshu Zheng , Mach Chen , Greg Mirsky | ||
| Last updated | 2023-03-06 | ||
| Replaces | draft-kumarzheng-bier-ping | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
RTGDIR Early review
by Dhruv Dhody
Has issues
INTDIR Early review
by Brian Haberman
Almost ready
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Consensus: Waiting for Write-Up | |
| Document shepherd | Mankamana Prasad Mishra | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Yes | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | mankamana mishra <mankamis@cisco.com> |
draft-ietf-bier-ping-08
Network Work group N. Kumar
Internet-Draft C. Pignataro
Intended status: Standards Track Cisco Systems, Inc.
Expires: 7 September 2023 N. Akiya
Big Switch Networks
L. Zheng
Individual Contributor
M. Chen
Huawei Technologies
G. Mirsky
Ericsson
6 March 2023
BIER Ping and Trace
draft-ietf-bier-ping-08
Abstract
Bit Index Explicit Replication (BIER) is an architecture that
provides optimal multicast forwarding through a "BIER domain" without
requiring intermediate routers to maintain any multicast related per-
flow state. BIER also does not require any explicit tree-building
protocol for its operation. A multicast data packet enters a BIER
domain at a "Bit-Forwarding Ingress Router" (BFIR), and leaves the
BIER domain at one or more "Bit-Forwarding Egress Routers" (BFERs).
The BFIR router adds a BIER header to the packet. The BIER header
contains a bit-string in which each bit represents exactly one BFER
to forward the packet to. The set of BFERs to which the multicast
packet needs to be forwarded is expressed by setting the bits that
correspond to those routers in the BIER header.
This document describes the mechanism and basic BIER OAM packet
format that can be used to perform failure detection and isolation on
the BIER data plane.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Kumar, et al. Expires 7 September 2023 [Page 1]
Internet-Draft BIER Ping March 2023
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 7 September 2023.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions used in this document . . . . . . . . . . . . . . 3
2.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2.2. Requirements Language . . . . . . . . . . . . . . . . . . 4
3. BIER OAM . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. BIER OAM message format . . . . . . . . . . . . . . . . . 4
3.2. Return Code . . . . . . . . . . . . . . . . . . . . . . . 6
3.3. BIER OAM TLV . . . . . . . . . . . . . . . . . . . . . . 8
3.3.1. Original SI-BitString TLV . . . . . . . . . . . . . . 8
3.3.2. Target SI-BitString TLV . . . . . . . . . . . . . . . 9
3.3.3. Incoming SI-BitString TLV . . . . . . . . . . . . . . 10
3.3.4. Downstream Mapping TLV . . . . . . . . . . . . . . . 10
3.3.5. Responder BFER TLV . . . . . . . . . . . . . . . . . 13
3.3.6. Responder BFR TLV . . . . . . . . . . . . . . . . . . 13
3.3.7. Upstream Interface TLV . . . . . . . . . . . . . . . 14
3.3.8. Reply-To TLV . . . . . . . . . . . . . . . . . . . . 15
3.4. Multipath Entropy Data Encoding . . . . . . . . . . . . . 16
4. Procedures . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.1. BIER OAM Processing . . . . . . . . . . . . . . . . . . . 16
4.2. Per BFER ECMP Discovery . . . . . . . . . . . . . . . . . 17
4.3. Sending BIER Echo Request . . . . . . . . . . . . . . . . 17
4.4. Receiving BIER Echo Request . . . . . . . . . . . . . . . 18
4.5. Sending Echo Reply . . . . . . . . . . . . . . . . . . . 20
4.6. Receiving Echo Reply . . . . . . . . . . . . . . . . . . 21
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22
Kumar, et al. Expires 7 September 2023 [Page 2]
Internet-Draft BIER Ping March 2023
5.1. BIER OAM Registry . . . . . . . . . . . . . . . . . . . . 22
5.2. Message Types, Reply Modes, Return Codes . . . . . . . . 22
5.3. TLVs . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6. Security Considerations . . . . . . . . . . . . . . . . . . . 23
7. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 23
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.1. Normative References . . . . . . . . . . . . . . . . . . 23
8.2. Informative References . . . . . . . . . . . . . . . . . 24
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 24
1. Introduction
[RFC8279] introduces and explains BIER architecture that provides
optimal multicast forwarding through a "BIER domain" without
requiring intermediate routers to maintain any multicast related per-
flow state. BIER also does not require any explicit tree-building
protocol for its operation. A multicast data packet enters a BIER
domain at a "Bit-Forwarding Ingress Router" (BFIR), and leaves the
BIER domain at one or more "Bit-Forwarding Egress Routers" (BFERs).
The BFIR router adds a BIER header to the packet. The BIER header
contains a bit-string in which each bit represents exactly one BFER
to forward the packet to. The set of BFERs to which the multicast
packet needs to be forwarded is expressed by setting the bits that
correspond to those routers in the BIER header.
This document describes the mechanism and basic BIER Operations,
Administration, and Maintenance (OAM) packet format that can be used
to perform failure detection and isolation on the BIER data plane
without any dependency on other layers like the IP layer.
2. Conventions used in this document
2.1. Terminology
BFER - Bit Forwarding Egress Router
BFIR - Bit Forwarding Ingress Router
BIER - Bit Index Explicit Replication
DDMAP - Downstream Detailed Mapping TLV
ECMP - Equal Cost Multi-Path
OAM - Operation, Administration, and Maintenance
SI - Set Identifier
Kumar, et al. Expires 7 September 2023 [Page 3]
Internet-Draft BIER Ping March 2023
2.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. BIER OAM
BIER OAM is defined to stay within the BIER layer by directly
following the BIER header without mandating the need for IP header.
[RFC8296] defines a 4-bit field as "Proto" to identify the payload
following the BIER header. When the payload is BIER OAM, the "Proto"
field will be set to 5 as defined in [RFC8296]
3.1. BIER OAM message format
The BIER OAM packet header format that follows BIER header is as
follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ver | Message Type | Proto | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OAM Message Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Message Type Dependent Data ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Ver
Set to 1.
Message Type
This document defines the following Message Types:
Type Value Field
-------- ---------------
1 BIER Echo Request
2 BIER Echo Reply
Proto
This field is used to define if there is any data packet
Kumar, et al. Expires 7 September 2023 [Page 4]
Internet-Draft BIER Ping March 2023
immediately following the OAM payload which is used for passive
OAM functionality. This field is set to 0 if there is no data
packet following OAM payload.
OAM Message Length
This field defines the length of the OAM message including the
header and Dependent Data field.
The Echo Request/Reply header format is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ver | Echo Req/Rep | Proto | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| QTF | RTF | Reply mode | Return Code | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sender's Handle |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Sent |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Sent |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Received |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TimeStamp Received |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ TLVs ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Proto
Set to 0 for Echo Request/Reply header.
QTF
Querier Timestamp Format. When set to 2, the Timestamp Sent field
is (in seconds and microseconds, according to the Initiator's
clock) in NTP format [RFC5905]. When set to 3, the timestamp
format is in IEEE 1588-2008 (1588v2) Precision Time Protocol
format. Any other value MAY be considered as sanity check failure
RTF
Responder Timestamp Format. When set to 2, the Timestamp Received
field is (in seconds and microseconds, according to the
Initiator's clock) in NTP format [RFC5905]. When set to 3, the
Kumar, et al. Expires 7 September 2023 [Page 5]
Internet-Draft BIER Ping March 2023
timestamp format is in IEEE 1588-2008 (1588v2) Precision Time
Protocol format. Any other value MAY be considered as sanity
check failure.
Reply mode
The Reply mode is set to one of the below:
Value Meaning
-------- ---------------
1 Do not Reply
2 Reply via IPv4/IPv6 UDP packet.
3 Reply via BIER packet
When Reply mode is set to 1, the receiver will not send any reply.
This mode can be used for unidirectional path validation. When the
Reply mode is set to 2, the Responder BFR encapsulates the Echo reply
payload with IP header. When the Initiator intends to validate the
return BIER path, the Reply mode will be set to 3 so that the
Responder BFR will encapsulates the Echo Reply with the BIER header.
Return Code
Set to zero if Type is "BIER Echo Request". Set to one of the
value defined in section 3.2, if Type is "BIER Echo Reply".
Reserved
Set to all zero value.
Sender's Handle, Sequence Number, and Timestamp
The Sender's Handle is filled by the Initiator, and returned
unchanged by responder BFR. This value can be used for matching
the replies to the request.
The Sequence Number is assigned by the Initiator and can be used
to detect any missed replies.
The Timestamp Sent is the time when the Echo Request is sent. The
TimeStamp Received in Echo Reply is the time (accordingly to
responding BFR clock) that the corresponding Echo Request was
received. The format depends on the QTF/RTF value.
TLVs
Carries the TLVs as defined in Section 3.3.
3.2. Return Code
The responder uses the Return Code field to reply with a validity
check or other error message to Initiator. It does not carry any
meaning in Echo Request and MUST be set to zero.
Kumar, et al. Expires 7 September 2023 [Page 6]
Internet-Draft BIER Ping March 2023
The Return Code can be one of the following:
Value Value Meaning
------ ---------------
0 No return code
1 Malformed Echo Request received
2 One or more of the TLVs is not supported
3 Replying BFR is the only BFER in header Bitstring
4 Replying BFR is one of the BFER in header Bitstring
5 Packet-Forward-Success
6 Invalid Multipath Info Request
8 No matching entry in the forwarding table
9 Set-Identifier Mismatch
10 DDMAP Mismatch
"No return code" will be used by Initiator in the Echo Request. This
value MUST NOT be used in Echo Reply.
"Malformed Echo Request received" will be used by any BFR if the
received Echo Request packet is not properly formatted.
When a receiver does not support any TLV included in the Echo
Request, the Return code will be set to "One or more of the TLVs is
not supported" carrying the respective TLVs.
When the received header BitString in the Echo Request packet
contains only its Bit-ID, "Replying BFR is the only BFER in header
BitString" is set in the reply. This value implies that the receiver
is BFER and the packet is not forwarded to any more neighbors.
When the received header BitString in the Echo Request packet
contains its Bit-ID in addition to other Bit-IDs, "Replying BFR is
one of the BFER in header BitString" is set in the reply. This value
implies that the responder is a BFER and the packet is further
forwarded to one or more neighbors.
Any transit BFR will send the Echo Reply with "Packet-Forward-
Success", if the TLV in the received Echo Request is understood and
forwarding table has forwarding entries for the BitString. This
behavior is demonstrated by a transit BFR during traceroute mode.
When the Echo Request is received with multipath info for more than
one BFER, the Return Code is set to "Invalid Multipath Info Request".
If the BitString cannot be matched in the local forwarding table, the
BFR will use "No matching entry in the forwarding table" in the
reply.
Kumar, et al. Expires 7 September 2023 [Page 7]
Internet-Draft BIER Ping March 2023
If the BIER-MPLS label in the received Echo Request is not the one
assigned for SI in Original SI-BitString TLV, "Set-Identifier
Mismatch" is set in order to report the mismatch.
3.3. BIER OAM TLV
This section defines various TLVs that can be used in BIER OAM
packet. The TLVs (Type-Length-Value tuples) have the following
format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Value ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
TLV Types are defined below; Length is the length of the Value field
in octets. The Value field depends on the TLV Type.
3.3.1. Original SI-BitString TLV
The Original SI-BitString TLV carries the set of BFER and carries the
same BitString that Initiator includes in the BIER header. This TLV
has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Sub-domain ID |BS Len| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (first 32 bits) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (last 32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Set ID field is set to the value of the Set Identifier to which the
BitString belongs to. This value is derived as defined in [RFC8279]
Sub-domain ID is set to the Sub-domain value to which BFER in
BitString belongs to.
Kumar, et al. Expires 7 September 2023 [Page 8]
Internet-Draft BIER Ping March 2023
BS Len is set based on the length of BitString as defined in
[RFC8296]
The BitString field carries the set of BFR-IDs that Initiator will
include in the BIER header. This TLV MUST be included by Initiator
in Echo Request packet
Any Initiator MUST include this TLV in the Echo Request packet.
3.3.2. Target SI-BitString TLV
The Target SI-BitString TLV carries the set of BFER from which the
Initiator expects the reply from.This TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 2 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Sub-domain ID |BS Len| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (first 32 bits) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (last 32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Set ID field is set to the Set Identifier to which the BitString
belongs to. This value is derived as defined in [RFC8279]
Sub-domain ID is set to the Sub-domain value to which BFER in
BitString belongs to.
BS Len is set based on the length of BitString as defined in
[RFC8296]
The BitString field carries the set of BFR-IDs of BFER(s) that
Initiator expects the response from. The BitString in this TLV may
be different from the BitString in the BIER header and allows to
control the BFER responding to the Echo Request. This TLV MUST be
included by Initiator in BIER OAM packet if the Downstream Mapping
TLV (section 3.3.4) is included.
Kumar, et al. Expires 7 September 2023 [Page 9]
Internet-Draft BIER Ping March 2023
3.3.3. Incoming SI-BitString TLV
The Incoming SI-BitString TLV will be included by Responder BFR in
Reply message and copies the BitString from BIER header of incoming
Echo Request message. This TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 3 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Sub-domain ID |BS Len| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (first 32 bits) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (last 32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Set ID field is set to the Set Identifier to which the BitString
belongs to. This value is derived as defined in [RFC8279]
Sub-domain ID is set to the Sub-domain value to which BFER in
BitString belongs to.
BS Len is set based on the length of BitString as defined in
[RFC8296]
The BitString field copies the BitString from the BIER header of the
incoming Echo Request. A Responder BFR SHOULD include this TLV in
Echo Reply if the Echo Request is received with I flag set in
Downstream Mapping TLV.
An Initiator MUST NOT include this TLV in Echo Request.
3.3.4. Downstream Mapping TLV
This TLV has the following format:
Kumar, et al. Expires 7 September 2023 [Page 10]
Internet-Draft BIER Ping March 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 4 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MTU | Address Type | Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream Address (4 or 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Downstream Interface Address (4 or 16 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sub-tlv Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
. .
. List of Sub-TLVs .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MTU
Set to MTU value of outgoing interface.
Address Type
The Address Type indicates the address type and length of IP
address for the downstream interface. The Address type is set to
one of the below:
Type Addr. Type DA Length DIA Length
------- --------------- ---------- ----------
1 IPv4 Numbered 4 4
2 IPv4 Unnumbered 4 4
3 IPv6 Numbered 16 16
4 IPv6 Unnumbered 16 4
DA Length - Downstream Address field Length
DIA Length - Downstream Interface Address field Length
Flags
The Flags field has the following format:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
| Rsvd |I|
+-+-+-+-+-+-+-+-+
When I flag is set, the Responding BFR MUST include the Incoming SI-
BitString TLV in Echo Reply message.
Kumar, et al. Expires 7 September 2023 [Page 11]
Internet-Draft BIER Ping March 2023
Downstream Address and Downstream Interface Address
If the Address Type is 1, the Downstream Address MUST be set to
IPV4 BFR-Prefix of downstream BFR and Downstream Interface Address
is set to the downstream interface address.
If the Address Type is 2, the Downstream Address MUST be set to
IPV4 BFR-Prefix of downstream BFR and Downstream Interface Address
is set to the index assigned by upstream BFR to the interface.
If the Address Type is 3, the Downstream Address MUST be set to
IPV6 BFR-Prefix of downstream BFR and Downstream Interface Address
is set to the downstream interface address.
If the Address Type is 4, the Downstream Address MUST be set to
IPv6 BFR-Prefix of downstream BFR and Downstream Interface Address
is set to the index assigned by upstream BFR to the interface.
3.3.4.1. Downstream Detailed Mapping Sub-TLVs
This section defines the optional Sub-TLVs that can be included in
Downstream Mapping TLV.
Sub-TLV Type Value
------------ -------------
1 Multipath Entropy Data
2 Egress BitString
3.3.4.1.1. Multipath Entropy Data
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|M| Reserved | |
+-+-+-+-+-+-+-+-+-+ |
| |
| (Multipath Information) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
M Flag
This flag is set to 0 if all packets will be forwarded out through
the interface defined in the Downstream Mapping TLV. When set to
1, Multipath Information will be defined by the Bit masked Entropy
data.
Multipath Information
Entropy Data encoded as defined in section 3.4
Kumar, et al. Expires 7 September 2023 [Page 12]
Internet-Draft BIER Ping March 2023
3.3.4.1.2. Egress BitString
Responder BFR MAY include this Sub-TLV with the rewritten BitString
in the outgoing interface as defined in section 6.1 of [RFC8279]
0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Sub-domain ID |BS Len| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (first 32 bits) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (last 32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.3.5. Responder BFER TLV
The BFER replying to the request MAY include the Responder BFER TLV.
This TLV identifies the originator of BIER Echo Reply. This TLV has
the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 5 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | BFR-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
BFR-ID
The BFR-ID field carries the BFR-ID of replying BFER. This TLV
MAY be included by Responding BFER in BIER Echo Reply packet.
3.3.6. Responder BFR TLV
Any transit BFR replying to the request MAY include the Responder BFR
TLV. This is used to identify the replying BFR without BFR-ID. This
TLV has the following format:
Kumar, et al. Expires 7 September 2023 [Page 13]
Internet-Draft BIER Ping March 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = 6 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Address Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ BFR-Prefix (4 or 16 bytes) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Length
The Length field varies depending on the Address Type.
Address Type
Set to 1 for IPv4 or 2 for IPv6.
BFR-Prefix
This field carries the local BFR-Prefix of the replying BFR. This
TLV MAY be included by Responding BFR in BIER Echo Reply packet.
3.3.7. Upstream Interface TLV
The BFR replying to the request MUST include the Upstream Interface
TLV. This TLV identifies the incoming interface and the BIER-MPLS
label in the incoming Echo Request. This TLV has the following
format:
Kumar, et al. Expires 7 September 2023 [Page 14]
Internet-Draft BIER Ping March 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = 7 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Address Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Upstream Address (4 or 16 bytes) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Length
The Length field varies depending on the Address Type.
Address Type
Set to 1 for IPv4 numbered, 2 for IPv4 Unnumbered 3 for IPv6
numbered or 4 for IPv6 Unnumbered.
Upstream Address
As defined in Section 3.3.4
3.3.8. Reply-To TLV
The Initiator BFR MAY include Reply-To TLV in the Echo Request. This
TLV is used by transit BFR or BFER when the reply mode is 2. The IP
address will be used to generate the Echo Reply. This TLV has the
following format:
Kumar, et al. Expires 7 September 2023 [Page 15]
Internet-Draft BIER Ping March 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type = 8 | Length = variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Address Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Reply-To Address (4 or 16 bytes) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Length
The Length field varies depending on the Address Type.
Address Type
Set to 1 for IPv4 or 2 for IPv6.
Reply-To Address
Set to any locally configured address to which the Echo reply
should be sent.
3.4. Multipath Entropy Data Encoding
The size of the Entropy field in the BIER header is 20 bits as
defined in section 2 of [RFC8296]. This encoding is similar to the
Multipath Type 9 encoding defined in Section 3.4.1.1.1 of [RFC8029].
4. Procedures
This section describes aspects of Ping and traceroute operations.
4.1. BIER OAM Processing
A BIER OAM packet MUST be sent to the BIER control plane for OAM
processing if one of the following conditions is true:
* The receiving BFR is a BFER.
* TTL of BIER-MPLS Label expired.
* Router Alert label is present in the label stack.
Kumar, et al. Expires 7 September 2023 [Page 16]
Internet-Draft BIER Ping March 2023
4.2. Per BFER ECMP Discovery
As defined in [RFC8279], BIER follows the unicast forwarding path and
allows load balancing over ECMP paths between BFIR and BFER. BIER
OAM MUST support ECMP path discovery between a BFIR and a given BFER
and MUST support path validation and failure detection of any
particular ECMP path between BFIR and BFER.
[RFC8296] proposes the BIER header with the Entropy field that can be
leveraged to exercise all ECMP paths. The Initiator/BFIR will use
traceroute message to query each hop about the Entropy information
for each of the downstream paths. To avoid complexity, it is
suggested that the ECMP query is performed per BFER by carrying
required information in BIER OAM message.
The Initiator MUST include Multipath Entropy Data Sub-TLV in
Downstream Mapping TLV. It MUST also include the BFER in BitString
TLV to which the Multipath query is performed.
Any transit BFR will reply with Bit-masked Entropy for each
downstream path as defined in [RFC8029]
4.3. Sending BIER Echo Request
The Initiator MUST set the Message Type as 1 and Return Code as 0.
The Proto field in OAM packet MUST be set to 0. The choice of the
Sender's Handle and Sequence Number is a local matter to the
Initiator and SHOULD increment the Sequence Number by 1 for every
subsequent Echo Request. The QTF field is set to Initiator's local
timestamp format and TimeStamp Sent field is set to the time that the
Echo Request is sent.
The Initiator MUST include Original SI-BitString TLV. The Initiator
MUST NOT include more than one Original SI-BitString TLV. The
Initiator infers the Set Identifier value and Sub-domain ID value
from the respective BitString that will be included in the BIER
header of the packet and includes the values in "SI" and Sub-Domain
ID fields respectively.
In Ping mode, the Initiator MAY include Target SI-BitString TLV to
control the responding BFER(s) by listing all the BFERs from which
the Initiator expects a response. In the trace route mode, the
Initiator MAY include Target SI-Bitstring TLV to control the path
trace towards any specific BFER or set of BFERs. The Initiator on
receiving a reply with Return code as "Replying BFR is the only BFER
in header Bitstring" or "Replying router is one of the BFER in header
Bitstring", SHOULD unset the respective BFR-id from Target SI-
BitString for any subsequent Echo Request.
Kumar, et al. Expires 7 September 2023 [Page 17]
Internet-Draft BIER Ping March 2023
When the Reply mode is set to 2, the Initiator MUST include Reply-To
TLV (section 3.3.8) in the Echo Request. The Initiator MUST also
listen to the UDP port defined in this TLV and process any segment
received with destination port as the value defined in the TLV and
sent to control plane for BIER OAM payload processing.
The Initiator MAY include Downstream Mapping TLV (section 3.3.4) in
the Echo Request to query additional information from transit BFRs
and BFERs. In case of ECMP discovery, the Initiator MUST include the
Multipath Entropy Data Sub-TLV and SHOULD set the Target SI-BitString
TLV carrying a specific BFER ID.
The Initiator MUST encapsulate the OAM packet with BIER header and
MUST set the Proto as 5 and further encapsulates with BIER-MPLS
label. In ping mode, the BIER-MPLS Label TTL MUST be set to 255. In
traceroute mode, the BIER-MPLS Label TTL is set successively starting
from 1 and MUST stop sending the Echo Request if it receives a reply
with Return code as "Replying router is the only BFER in BIER header
Bitstring" from all BFER listed in Target SI-BitString TLV.
4.4. Receiving BIER Echo Request
Sending a BIER OAM Echo Request to control plane for payload
processing is triggered as mentioned in section 4.1.
Any BFR on receiving Echo Request MUST perform the basic sanity
check. If the BFR cannot parse the OAM Dependent data payload
completely because the value in the OAM Message Length field is
incorrect, BFR MUST send Echo Reply with Return Code set to
"Malformed Echo Request received" if the OAM Message Length is
incorrect. If the packet sanity check is fine, it SHOULD initiate
the below set of variables:
Reply-Flag
This flag is initially set to 1.
Interface-I
The incoming interface on which the Echo Request was received.
This MAY be used to validate the Downstream Detailed Mapping TLV
(DDMAP) info and to populate the Upstream Interface TLV.
BIER-Label-L
The BIER-MPLS Label received as the top label of the received Echo
Request. This MAY be used to validate if the packet is traversing
the desired Set Identifier and sub-domain path.
Kumar, et al. Expires 7 September 2023 [Page 18]
Internet-Draft BIER Ping March 2023
Header-H
The BIER header of the received Echo Request. It can be used to
validate the DDMAP info and to populate the Incoming SI-BitString
TLV. Also, it can be used to perform Entropy calculation
considering a different field in the header and reply via
Multipath Entropy Data Sub-TLV.
BFR MUST initialize the Best-return-code variable to the null value.
BFR will populate the Interface-I with the identifier of the
interface over which the Echo Request is received, the top label in
the MPLS stack of the received Echo Request to BIER-Label-L, and the
BIER header to BIER-Header. If the received Echo Request carries
Target SI-BitString TLV, a BFR SHOULD run boolean AND operation
between BitString in Header-H and BitString in Target SI-BitString
TLV. If the resulting BitString is all-zero, reset Reply-Flag=0 and
go to section 4.5. Else:
* If the BIER-Label-L does not correspond to the local label
assigned for {sub-domain, BitStringLen, SI} in Original SI-
BitString TLV, Set the Best-return-code to "Set-Identifier
Mismatch" and Go to section 4.5.
* /* This step allows the detection of a synchronization problem in
the upstream BFR between BIER-Label and {sub-domain, BitStringLen,
SI} that might cause an unintended packet leak between sub-domains.
*/
* Set the Best-return-code to "One or more of the TLVsis not
supported" if any of the TLVs in the Echo Request message is not
supported. Go to section 4.5.
* If the BitString in Header-H does not match the BitString in
Egress BitString Sub-TLV of DDMAP TLV, set the Best-return-code to
"DDMAP Mismatch" and go to section 4.5. When there are more than
one DDMAP TLV in the received Request packet, the Downstream
Address and Downstream Interface Address should be matched with
Interface-I to identify the right DDMAP TLV and then perform the
BitString match.
* /* This step allows the detection of a deviation between the BIER
control plane and the BIER forwarding plane in the upstream node that
may result in a forwarding loop or packet duplication. */
* Set the Best-return-code to "Invalid Multipath Info Request", when
the DDMAP TLV carries Multipath Entropy Data Sub-TLV, and if the
Target SI-BitString TLV in the received Echo Request carries more
than 1 BFER id. Go to section 4.5. Else, list the ECMP
Kumar, et al. Expires 7 September 2023 [Page 19]
Internet-Draft BIER Ping March 2023
downstream neighbors to reach BFR-id in Target SI-BitString TLV,
calculate the Entropy considering the BitString in Header-H and
Multipath Entropy Data Sub-TLV from received Echo Request. Store
the Data for each Downstream interface in a temporary variable.
Set the Best-return-code to 5 (Packet-Forward-Success) and goto
Section 4.5
* /* This step instructs the node to calculate the Entropy Data for
each downstream interface to reach the BFER in Target SI-BitString
TLV by considering the incoming BitString and Entropy Data.*/
* Set the Best-return-code to "Replying router is the only BFER in
BIER header Bitstring", and go to section 4.5 if the responder is
BFER and there are no more bits in BIER header Bitstring left for
forwarding.
* Set the Best-return-code to "Replying router is one of the BFER in
BIER header Bitstring", and include Downstream Mapping TLV, if the
responder is BFER and there are more bits in BitString left for
forwarding. Also, include the Multipath information as defined in
Section 4.2 if the received Echo Request carries Multipath Entropy
Data Sub-TLV. Go to section 4.5.
* Set the Best-return-code to "No matching entry in the forwarding
table", if the forwarding lookup defined in section 6.5 of
[RFC8279] does not match any entry for the received BitString in
BIER header.
* /* This step allows the detection of the missing BFR-id in the
node's BIER forwarding table. It is difficult to detect the absence
of the BFR-id if the Request includes more than one BFR-ids in the
BitString and so may need to include the BFER-id that is not
responding to detect such failure. */
* Set the Best-return-code to "Packet-Forward-Success", and include
Downstream Mapping TLV. Go to section 4.5
4.5. Sending Echo Reply
If Reply-Flag=0, BFR MUST release the variables and MUST not send any
response to the Initiator. If Reply-Flag=1, proceed as below:
The Responder BFR SHOULD include the BitString from Header-H to
Incoming SI-BitString TLV and include the Set ID, Sub-domain ID and
BS Len that corresponds to BIER-Label-L. Responder BFR SHOULD
include the Upstream Interface TLV and populate the address from
Interface-I.
Kumar, et al. Expires 7 September 2023 [Page 20]
Internet-Draft BIER Ping March 2023
When the Best-return-code is "Replying BFR is one of the BFER in
header Bitstring", it MUST include Responder BFER TLV.
If the received Echo Request had DDMAP with Multipath Entropy Data
Sub-TLV, Responder BFR MUST include DDMAP as defined in
Section 3.3.4 for each outgoing interface over which the packet
will be replicated and include the respective Multipath Entropy
Data Sub-TLV. For each outgoing interface, respective Egress
BitString MUST be included in DDMAP TLV.
If the received Echo Request had DDMAP without Multipath Entropy
Data Sub-TLV, Responder BFR MUST include DDMAP as defined in
Section 3.3.4 for each outgoing interface over which the packet
will be replicated. For each outgoing interface, respective
Egress BitString MUST be included in DDMAP TLV.
When the Best-return-code is "Replying BFR is the only BFER in header
Bitstring", it MUST include Responder BFER TLV.
The Responder MUST set the Message Type as 2 and Return Code as Best-
return-code. The Proto field MUST be set to 0.
The Echo Reply can be sent either as BIER-encapsulated or IP/UDP
encapsulated depending on the Reply mode in received Echo Request.
When the Reply mode in received Echo Request is set to 3, Responder
appends BIER header listing the BitString with BFIR ID (from Header-
H), set the Proto to 5 and set the BFIR as 0. When the Reply mode in
received Echo Request is set to 2, Responder encapsulates with IP/UDP
header. The UDP destination port MUST be set to TBD1, and the source
port MAY be set to TBD1 or other random local value. The source IP
is any local address of the responder and destination IP is derived
from Reply-To TLV.
4.6. Receiving Echo Reply
The Initiator upon receiving the Echo Reply will use the Sender's
Handle to match with Echo Request sent. If no match is found, the
Initiator MUST ignore the Echo Reply.
If receiving Echo Reply have Downstream Mapping, the Initiator SHOULD
copy the same to subsequent Echo Request(s).
If one of the Echo Reply is received with Return Code as "Replying
BFR is one of the BFER in header Bitstring", it SHOULD reset the BFR-
id of the responder from Target SI-BisString TLV in subsequent Echo
Request.
Kumar, et al. Expires 7 September 2023 [Page 21]
Internet-Draft BIER Ping March 2023
/* This step helps avoid any BFR that is both BFER and transit BFR to
respond with Echo Reply continuously. */
5. IANA Considerations
This document requests a UDP port TBD1 to be allocated by IANA for
BIER Echo.
This document requests the IANA to create and manage the below
registries and sub-registries:
5.1. BIER OAM Registry
IANA is requested to create and maintain "BIER OAM Parameters"
registry.
5.2. Message Types, Reply Modes, Return Codes
IANA is requested to create a "Message Type" sub-registry under "BIER
OAM Parameters" registry and assign the Message Types defined in
section 3.1
IANA is requested to create a "Echo Reply Mode" sub-registry under
"BIER OAM Parameters" registry and assign the Echo Reply Modes
defined in section 3.1
IANA is requested to create a "Echo Return Codes" sub-registry under
"BIER OAM Parameters" registry and assign the Return Codes defined in
section 3.2
5.3. TLVs
The TLVs and Sub-TLVs defined in this document is not limited to Echo
Request or Reply message types and is applicable for other message
types. The TLVs and Sub-TLVs requested by this document for IANA
consideration are the following:
Type Sub-Type Value Field
------- -------- -----------
1 Original SI-BitString
2 Target SI-BitString
3 Incoming SI-BitString
4 Downstream Mapping
4 1 Multipath Entropy Data
4 2 Egress BitString
5 Responder BFER
6 Responder BFR
7 Upstream Interface
Kumar, et al. Expires 7 September 2023 [Page 22]
Internet-Draft BIER Ping March 2023
6. Security Considerations
The security consideration for BIER Ping is similar to ICMP [RFC0792]
or LSP Ping [RFC8029], [RFC6425]. As with ICMP or LSP Ping, BFR can
be exposed to Denial- of-Service (DoS) attacks, and it is RECOMMENDED
to regulate the BIER Ping packet flow to the control plane. A rate
limiter SHOULD be applied to avoid any attack.
As with ICMP or LSP Ping, a traceroute can be used to obtain network
information. It is RECOMMENDED that the implementation checks the
integrity of BFIR of the Echo messages against any local secured list
before processing the message further
7. Acknowledgement
The authors would like to thank Antoni Przygienda, Eric Rosen, Faisal
Iqbal, Jeffrey (Zhaohui) Zhang,DIA Length - Downstream Interface
Address field Length and Shell Nakash for their review and comments.
The authors would like to thank Mankamana Mishra for his thorough
review and comments.
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC5905] Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
"Network Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
<https://www.rfc-editor.org/info/rfc5905>.
[RFC8029] Kompella, K., Swallow, G., Pignataro, C., Ed., Kumar, N.,
Aldrin, S., and M. Chen, "Detecting Multiprotocol Label
Switched (MPLS) Data-Plane Failures", RFC 8029,
DOI 10.17487/RFC8029, March 2017,
<https://www.rfc-editor.org/info/rfc8029>.
Kumar, et al. Expires 7 September 2023 [Page 23]
Internet-Draft BIER Ping March 2023
[RFC8279] Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
Explicit Replication (BIER)", RFC 8279,
DOI 10.17487/RFC8279, November 2017,
<https://www.rfc-editor.org/info/rfc8279>.
[RFC8296] Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
Tantsura, J., Aldrin, S., and I. Meilik, "Encapsulation
for Bit Index Explicit Replication (BIER) in MPLS and Non-
MPLS Networks", RFC 8296, DOI 10.17487/RFC8296, January
2018, <https://www.rfc-editor.org/info/rfc8296>.
[RFC6425] Saxena, S., Ed., Swallow, G., Ali, Z., Farrel, A.,
Yasukawa, S., and T. Nadeau, "Detecting Data-Plane
Failures in Point-to-Multipoint MPLS - Extensions to LSP
Ping", RFC 6425, DOI 10.17487/RFC6425, November 2011,
<https://www.rfc-editor.org/info/rfc6425>.
8.2. Informative References
[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, DOI 10.17487/RFC0792, September 1981,
<https://www.rfc-editor.org/info/rfc792>.
Authors' Addresses
Nagendra Kumar
Cisco Systems, Inc.
7200 Kit Creek Road
Research Triangle Park, NC 27709
US
Email: naikumar@cisco.com
Carlos Pignataro
Cisco Systems, Inc.
7200 Kit Creek Road
Research Triangle Park, NC 27709-4987
US
Email: cpignata@cisco.com
Nobo Akiya
Big Switch Networks
Japan
Email: nobo.akiya.dev@gmail.com
Kumar, et al. Expires 7 September 2023 [Page 24]
Internet-Draft BIER Ping March 2023
Lianshu Zheng
Individual Contributor
China
Email: veronique_cheng@hotmail.com
Mach Chen
Huawei Technologies
Email: mach.chen@huawei.com
Greg Mirsky
Ericsson
Email: gregimirsky@gmail.com
Kumar, et al. Expires 7 September 2023 [Page 25]